Bobcat E35 Rubber Tracks & Parts

The Bobcat E35 runs a 300x52.5Nx84 track: 300 mm across the tread, 52.5 mm between links, 84 links around. Cut for digging, trenching, backfill and tight-quarters work and shipped free to the lower 48.

What the numbers mean on a Bobcat E35

  • 300x52.5Nx84 — 300 mm tread width (about 12"), 52.5 mm pitch, 84 links, narrow guide lugs

Width is the tread face, pitch is the distance between drive lugs, and links is the count around the loop. All three have to match — a track one link off will not tension correctly no matter how close the width is.

Tread choice for the Bobcat E35

Size gets the track on the machine; tread decides how it works and how long it lasts. What we stock for this one:

  • MX — mixed and hard surfaces. A durable general-duty excavator tread

Bobcat E35 at a glance

  • Operating weight — 7,826 lb
  • Engine — 24 hp

Undercarriage parts for the Bobcat E35

Rollers, idlers and sprockets wear on the same clock as the track. Fitting new rubber over a hooked sprocket or a seized roller is the fastest way to lose the new track — check these while the tracks are off:

Where more than one part number is listed, Bobcat changed that component across serial ranges. Match the number stamped on the part you are replacing, or send us the machine serial and we will pick it.

How these wear

Excavator undercarriages load one side hard on slew and travel, so link cracking usually shows up before the tread wears out. Replace in pairs where you can: a new track running against a stretched one loads the drive unevenly and you will feel it in the steering.

Same track, other machines

Track size follows undercarriage geometry, not brand, so 300x52.5Nx84 shows up on machines from several makers. If you run any of these alongside the Bobcat E35, it is the same belt:

Not sure which you are running? Read the size off the inside of the old track, or call (850) 816-7898 and we will pull it off the machine record. The Track Finder works by make and model too.

More Bobcat undercarriage

Free US Shipping100% Fit GuaranteePremium OEM Quality

Shop Parts
Bobcat E35 mini excavator

Track sizes

Heavy-Duty Rubber Tracks for E35

|
  • 300x52.5Nx84 Directional Rubber Track
    Bobcat E35 300x52.5Nx84 300x52.5Nx84
    • Heavy Duty | 300x52.5Nx84
    $981.50$943.75

    In stock

    Add to quote
  • 300x52.5Wx84 Block Rubber Track
    Bobcat E35 300x52.5Wx84 300x52.5Wx84
    • Heavy Duty | 300x52.5Wx84
    $1,149.00$999.00

    In stock

    Add to quote
  • 300x52.5Wx84 Bridgestone Rubber Track | MX
    Bobcat E35 300x52.5Wx84
    • Bridgestone | 300x52.5Wx84

    Request quote

    Add to quote

  • 100% Virgin Rubber

    Engineered to resist chunking, tearing, and cutting in harsh, abrasive environments.

  • Continuous Steel Cords

    Jointless internal cable architecture eliminates structural weak points and maximizes overall tensile strength.

  • Drop-Forged Links

    Precision heat-treated guide lugs ensure exact sprocket engagement and prevent de-tracking under heavy side-loads.

  • Corrosion Resistant

    The internal steel framework is fully encapsulated to prevent oxidation, rust, and moisture penetration.

  • Reinforced Sidewalls

    Extra-thick vulcanized rubber and tapered edge profiles protect against curb slashing and lateral impacts from jobsite debris.

  • Low-Vibration Tread

    Optimized lug spacing and pitch geometry absorb shock, reducing undercarriage wear and minimizing cabin vibration.

Bobcat E35 Rubber Tracks & Parts fitment data

Machine Performance

Operating Weight7826 lb
Horsepower24 HP
ROC / Bucket Force8500 lb

Hydraulics & Lift

Standard Flow11 GPM

Fitment & Part Numbers

Track Size300x52.5x84
Sprocket6
Idler7
Roller7

Real Bobcat E35 Track Installs

Upgrade your equipment with confidence. Proven and trusted by contractors nationwide—click any jobsite photo below to shop the exact tread pattern your machine demands.

Bobcat E35 rubber tracks for compact equipment

Bobcat E35

Track Size: 300x52.5x84

Featured Tread: Directional

Shop verified-fit rubber tracks and undercarriage parts for the Bobcat E35 mini excavator. Merchant-confirmed sizes on this hub: 300 x 52.5N x 84. Available tread families include Multi-Bar (MX). When more than one size applies, match the undercarriage configuration rather than guessing from model alone.

Frequently Asked Questions

What size rubber tracks fit a Bobcat E35?
The Bobcat E35 can use 300x52.5x84 rubber tracks. Match the full size on the track you are replacing before you order. If your machine has more than one track setup, choose the width and guide style that matches the track currently on the machine.
Which tread patterns are available for the Bobcat E35?
Once the size is confirmed, choose the tread for the work the machine actually does. This Bobcat E35 page currently includes Mx. Use the tread pattern guide to compare traction, ride, cleanout, and wear before choosing a pattern.
Does TrackTECH carry undercarriage parts for the Bobcat E35?
Yes. When a matched part is available, this Bobcat E35 hub can show the drive sprocket, front or rear idlers, and rollers alongside the tracks. If you're replacing tracks, inspect the undercarriage at the same time—worn sprockets or rollers can shorten the life of a new set. You can also browse undercarriage parts.
Do Bobcat E35 tracks ship free?
Qualifying in-stock rubber track orders ship free by LTL to the lower 48. Same-day dispatch is available on qualifying in-stock orders placed before 12 PM CT; the actual delivery window depends on the exact item and ZIP code. See the shipping policy for details.
What warranty applies to TrackTECH rubber tracks?
TrackTECH rubber tracks on this hub are covered by the published 24-month / 1,500-hour warranty. Keep your proof of purchase and make sure fitment is confirmed before installation. See the warranty terms for coverage and claim requirements.