Ditch Witch JT2510 Rubber Tracks & Parts

The Ditch Witch JT2510 is cataloged in more than one track width — 180 / 230 mm. Pick the width your undercarriage is actually set up for, then choose tread for the ground you work. Free freight to the lower 48 on every track, 24-month warranty.

Which width fits your Ditch Witch JT2510

  • 230x72x39 — 230 mm (9") wide, 72 mm pitch, 39 links
  • 180x72x39 — 180 mm (7") wide, 72 mm pitch, 39 links

These are not interchangeable by preference — the width your machine takes is set by the roller frame and sprocket it left the factory with. Wider tread floats better on soft ground and spreads ground pressure; narrower runs cheaper, turns easier and clears tight spots. Measure the existing track across the tread face before you order.

Tread choice for the Ditch Witch JT2510

Size gets the track on the machine; tread decides how it works and how long it lasts. What we stock for this one:

  • C-Block — concrete, asphalt and hard-packed ground. Longest wear life and the least vibration on hard surfaces
  • Directional — digging, trenching and slope work. The standard excavator tread

If the machine splits its time between surfaces, buy for the ground you are on most — a hard-surface tread on constant mud will spin, and a bar tread on concrete will wear out in half the hours.

Parts we carry for the Ditch Witch JT2510

Tracks. Call for anything not shown online — we can usually source it.

How these wear

Drills sit still under load and travel short distances, so tracks usually age out from compound fatigue rather than mileage. Replace in pairs where you can: a new track running against a stretched one loads the drive unevenly and you will feel it in the steering.

Same track, other machines

Track size follows undercarriage geometry, not brand, so one of these sizes shows up on machines from several makers. If you run any of these alongside the Ditch Witch JT2510, it is the same belt:

Not sure which you are running? Read the size off the inside of the old track, or call (850) 816-7898 and we will pull it off the machine record. The Track Finder works by make and model too.

More Ditch Witch undercarriage

Free US Shipping100% Fit GuaranteePremium OEM Quality

Shop Parts

Track sizes

Heavy-Duty Rubber Tracks for JT2510

|
  • 180x72x39 Heavy Duty Rubber Track | C-Block
    Ditch Witch JT2510 180x72x39 C-Block
    • Heavy Duty | 180x72x39
    • Maximum Durability
    • Anti-Vibration
    • Cut & Tear Resistant
    $235.30$226.25

    In stock

    Add to quote
  • 180x72x39 Heavy Duty Rubber Track | Directional
    $235.30$226.25

    In stock

    Add to quote
  • 230x72x39 C Block Rubber Track
    $392.60$377.50

    In stock

    Add to quote
  • 180x72x39 Bridgestone Rubber Track | C-Block
    Ditch Witch JT2510 180x72x39 C-Block
    • Bridgestone | 180x72x39
    • Maximum Durability
    • Anti-Vibration
    • Cut & Tear Resistant

    Request quote

Which tread fits Ditch Witch JT2510?

Pick a tread for your jobsite — then buy above.
+ Recommended surface- Not the primary use— Application dependent
PatternBest UseKey TraitsRoadClayGravelMulchMudTurfAction
C-Block C-BlockHeavy-duty durability Built for maximum durability on abrasive jobsites, hard-pack surfaces, demolition debris, and mixed gravel.
  • Maximum Durability
  • Anti-Vibration
  • Cut & Tear Resistant
+++---View

Track construction features

  • 100% Virgin Rubber

    Engineered to resist chunking, tearing, and cutting in harsh, abrasive environments.

  • Continuous Steel Cords

    Jointless internal cable architecture eliminates structural weak points and maximizes overall tensile strength.

  • Drop-Forged Links

    Precision heat-treated guide lugs ensure exact sprocket engagement and prevent de-tracking under heavy side-loads.

  • Corrosion Resistant

    The internal steel framework is fully encapsulated to prevent oxidation, rust, and moisture penetration.

  • Reinforced Sidewalls

    Extra-thick vulcanized rubber and tapered edge profiles protect against curb slashing and lateral impacts from jobsite debris.

  • Low-Vibration Tread

    Optimized lug spacing and pitch geometry absorb shock, reducing undercarriage wear and minimizing cabin vibration.

Ditch Witch JT2510 Rubber Tracks & Parts fitment data

Verified-fit rubber tracks and undercarriage parts for the Ditch Witch JT2510. Confirm size and tread before ordering.

Frequently Asked Questions

What size rubber tracks fit a Ditch Witch JT2510?
The Ditch Witch JT2510 can use 180x72x39 or 230x72x39 rubber tracks. Match the full size on the track you are replacing before you order. If your machine has more than one track setup, choose the width and guide style that matches the track currently on the machine.