Ditch Witch SK500 Rubber Tracks & Parts

The Ditch Witch SK500 is cataloged in more than one track width — 180 / 230 mm. Pick the width your undercarriage is actually set up for, then choose tread for the ground you work. Free freight to the lower 48 on every track, 24-month warranty.

Which width fits your Ditch Witch SK500

  • 230x72x39 — 230 mm (9") wide, 72 mm pitch, 39 links
  • 180x72x39 — 180 mm (7") wide, 72 mm pitch, 39 links

These are not interchangeable by preference — the width your machine takes is set by the roller frame and sprocket it left the factory with. Wider tread floats better on soft ground and spreads ground pressure; narrower runs cheaper, turns easier and clears tight spots. Measure the existing track across the tread face before you order.

Tread choice for the Ditch Witch SK500

Size gets the track on the machine; tread decides how it works and how long it lasts. What we stock for this one:

  • C-Block — concrete, asphalt and hard-packed ground. Longest wear life and the least vibration on hard surfaces
  • Directional — digging, trenching and slope work. The standard excavator tread

If the machine splits its time between surfaces, buy for the ground you are on most — a hard-surface tread on constant mud will spin, and a bar tread on concrete will wear out in half the hours.

Undercarriage parts for the Ditch Witch SK500

Rollers, idlers and sprockets wear on the same clock as the track. Fitting new rubber over a hooked sprocket or a seized roller is the fastest way to lose the new track — check these while the tracks are off:

How these wear

Stand-on loaders spend their life on curbs, trailers and hard surfaces, so abrasion is the usual failure mode, not cracking. Replace in pairs where you can: a new track running against a stretched one loads the drive unevenly and you will feel it in the steering.

Same track, other machines

Track size follows undercarriage geometry, not brand, so one of these sizes shows up on machines from several makers. If you run any of these alongside the Ditch Witch SK500, it is the same belt:

Not sure which you are running? Read the size off the inside of the old track, or call (850) 816-7898 and we will pull it off the machine record. The Track Finder works by make and model too.

More Ditch Witch undercarriage

Free US Shipping100% Fit GuaranteePremium OEM Quality

Shop Parts
Ditch Witch SK500 mini track loader

Track sizes

Heavy-Duty Rubber Tracks for SK500

|
  • 230x72x39 c block heavy-duty rubber track
    Ditch Witch SK500 230x72x39 C-Block
    • Heavy Duty | 230x72x39
    • Maximum Durability
    • Anti-Vibration
    • Cut & Tear Resistant
    $392.60$377.50

    In stock

    Add to quote
  • 180x72x39 c-block heavy-duty rubber track
    Ditch Witch SK500 180x72x39 C-Block
    • Heavy Duty | 180x72x39
    • Maximum Durability
    • Anti-Vibration
    • Cut & Tear Resistant
    $235.30$226.25

    In stock

    Add to quote
  • 180x72x39 directional heavy-duty rubber track
    $235.30$226.25

    In stock

    Add to quote
  • Bridgestone 180x72x39 C-Block rubber track
    Ditch Witch SK500 180x72x39 C-Block
    • Bridgestone | 180x72x39
    • Maximum Durability
    • Anti-Vibration
    • Cut & Tear Resistant
    $497.90$479.00

    In stock

    Add to quote

Which tread fits Ditch Witch SK500?

Pick a tread for your jobsite — then buy above.
+ Recommended surface- Not the primary use Application dependent
PatternBest UseKey TraitsRoadClayGravelMulchMudTurfAction
C-Block C-BlockHeavy-duty durability Built for maximum durability on abrasive jobsites, hard-pack surfaces, demolition debris, and mixed gravel.
  • Maximum Durability
  • Anti-Vibration
  • Cut & Tear Resistant
+++---View

Track construction features

  • 100% Virgin Rubber

    Engineered to resist chunking, tearing, and cutting in harsh, abrasive environments.

  • Continuous Steel Cords

    Jointless internal cable architecture eliminates structural weak points and maximizes overall tensile strength.

  • Drop-Forged Links

    Precision heat-treated guide lugs ensure exact sprocket engagement and prevent de-tracking under heavy side-loads.

  • Corrosion Resistant

    The internal steel framework is fully encapsulated to prevent oxidation, rust, and moisture penetration.

  • Reinforced Sidewalls

    Extra-thick vulcanized rubber and tapered edge profiles protect against curb slashing and lateral impacts from jobsite debris.

  • Low-Vibration Tread

    Optimized lug spacing and pitch geometry absorb shock, reducing undercarriage wear and minimizing cabin vibration.

Ditch Witch SK500 Rubber Tracks & Parts fitment data

Verified-fit rubber tracks and undercarriage parts for the Ditch Witch SK500. Confirm size and tread before ordering.

Frequently Asked Questions

What size rubber tracks fit a Ditch Witch SK500?
Verified rubber track sizes for the Ditch Witch SK500 include 180x72x39, 230x72x39. Confirm the installed undercarriage configuration, guide type, and link count before ordering when more than one verified size applies.